Anchoring in Heavy Weather: Do Not Exceed the Design Limits of Anchor Equipment
Recently, a 23,000 DWT bulk carrier ran aground after dragging its anchor in strong winds at an anchorage, sounding another alarm for the shipping industry. When wind, wave and current conditions at an anchorage exceed the design limits of anchoring equipment, forcing the vessel to stay at anchor often leads to equipment failure, loss of vessel control, and even serious accidents. Anchor equipment was never designed to withstand extreme adverse weather conditions. Respecting its design boundaries, heaving up the anchor in time for open-water drifting or relocating to a sheltered anchorage before risks escalate, is the core principle for vessel safety in heavy weather.
I. Design Boundaries of Anchor Equipment: Defined by Equipment Number
The configuration of a vessel’s anchoring system is fundamentally determined by the Equipment Number (EN), a unified calculation system developed by the International Association of Classification Societies (IACS) and implemented by all classification societies. This standard defines the upper limit of anchor equipment capacity at its very foundation.
According to classification society rules, anchor equipment is explicitly designed for temporary anchorage in harbours or sheltered waters while awaiting berths, tides or pilots. It is not engineered to resist extreme weather in fully exposed open coastal areas, nor to brake a drifting vessel under dynamic loads.
Its design baseline comes with clear thresholds for wind, wave and current:
Under ideal still-water conditions: the design wind speed is approximately 25 m/s (about 50 knots), design current speed about 2.5 m/s (about 5 knots), with a scope of anchor chain 6 to 10 times the water depth.
Under realistic sea conditions with wave-induced dynamic loads: the design parameters drop significantly, corresponding to a wind speed of around 11 m/s (about 22 knots), current speed of about 1.5 m/s, and significant wave height no more than 2 m.
Industry data further shows that even with good seabed holding conditions, anchor equipment can withstand wind of around 48 knots in calm water. However, when the significant wave height reaches 2 metres, its wind resistance drops to 21 knots – a reduction of over 50%.
In other words, the windlass, anchor chain and flukes installed on board are all calculated on the premise of sheltered waters and moderate sea conditions. When an anchorage sees wind above Beaufort 6, swell over 1.5 m, combined with current of 2–3 knots, the wind-wave-current loads on the vessel already approach or even exceed the design baseline of the equipment. Staying at anchor in such conditions essentially forces the equipment to bear loads it was never intended to take.
II. Consequences of Overlimit Anchoring: From Dragging Anchor to Catastrophic Failure
When wind and waves exceed the design limits of anchor equipment, the risk does not stop at dragging anchor. It escalates step by step along the equipment chain, eventually leading to multiple types of accidents.
The most common outcome is anchor dragging. Poor seabed conditions and crowded anchorages already reduce anchor holding power. In heavy weather, vessel yawing and wave impact loads cause the anchor fluke to be repeatedly loaded and break out of the seabed, eventually resulting in uncontrolled drift. This sharply raises the risk of collision with nearby vessels, grounding, and contact with underwater obstacles – exactly what happened to the 23,000 DWT bulk carrier mentioned at the beginning.
More severe is structural failure of the equipment. Anchor chain shackles, common links and anchor crowns are prone to fracture under excessive dynamic loads. Windlass brake slippage, motor overload burnout and gearbox damage are also frequently reported. Industry statistics indicate that around 1% of trading vessels worldwide suffer lost anchor incidents each year, the vast majority of which are directly related to operating anchor equipment beyond its design conditions in heavy seas. Past incidents include windlass motor damage during anchor heaving in Beaufort 8 winds with 3-metre waves, total anchor loss under Beaufort 9 winds, and even fatal accidents caused by windlass explosion.
A common misconception among seafarers is that letting out more chain increases holding power. In reality, in heavy weather, an excessively long chain does not significantly improve seabed holding. Instead, it adds tensile load from the chain’s own weight, amplifies vessel yawing, and subjects the chain and windlass to greater alternating impact loads, accelerating equipment failure.
III. Correct Response: Anticipate Risks and Heave Anchor Promptly
In heavy weather, the key to safe anchorage is not how to hold on, but how to leave in advance. The safety management systems of many shipping companies define clear warning and action thresholds: when the forecast indicates wind > 25 knots (Beaufort 6), swell > 1.5 m, or current > 2–3 knots, the Master shall be notified immediately, the engine room shall be advised to stand by for heaving up the anchor, and preparations shall be made to leave the anchorage within 1–2 hours.
There are two clear safe options for action:
1. Relocate to a better-sheltered anchorage
If a sheltered anchorage with natural protection from wind and waves is available within a reasonable sailing distance, relocation should be the priority. When selecting a new anchorage, seabed type, water depth, swinging room and wind direction shall be fully considered. Muddy or clayey seabeds are preferred; water depth shall allow a safety margin of twice the draft plus wave height; and fairways, bridge areas, aquaculture zones and areas with dense underwater obstacles shall be avoided.
2. Drifting or slow steaming in open waters
If no suitable sheltered anchorage is nearby, or if the weather system develops too quickly for relocation, the vessel shall heave up the anchor without hesitation and proceed to open waters for drifting. Open waters provide ample manoeuvring space. By heading the bow into the wind and maintaining minimal speed against the waves, hull loads can be greatly reduced, and the vessel can avoid being driven onto shoals or obstacles. At the same time, the risks of anchor dragging and chain breakage are completely eliminated.
In terms of operation, timing is critical. Do not wait until wind fully strengthens and the anchor chain is under heavy tension to heave up, as this will put extreme load on the windlass and easily cause damage. The anchor should be heaved smoothly with engine assistance before the wind reaches the threshold and while vessel yawing is moderate. If anchor dragging has already occurred, the engine shall first be used to steady the vessel and relieve the chain tension before heaving, instead of pulling forcefully against the load.
Conclusion
Anchoring is one of the most basic ship operations, yet its risk boundaries are often overlooked due to familiarity. Anchor equipment is not an all-weather safeguard that can withstand storms. It has clear design limits and applicable scenarios.
For seafarers, understanding the capacity limits behind the Equipment Number, not overestimating chain length or equipment strength, conducting risk assessment at the early stage of weather warning, and taking decisive action before thresholds are breached, is the most responsible choice for vessel, equipment and crew safety. In heavy weather, the sound judgement to leave early protects far better than the courage to tough it out.
READ MORE
Safety
Iran Says Gas Carrier Hit Naval Mine and Exploded East of Strait of Hormuz
Safety
Another Exit for Sanctioned Ships? Best Oasis Announces OFAC Licence
Safety
Xinde Shipping Briefing: Hormuz Tanker Attacks, VLCC Rate Correction and China's Newbuilding Deals
Safety
Tanker Strikes Docked Riverboat in New Orleans; 32 Taken to Hospital
Safety
Maersk Hit by Another Cyberattack: Data Extracted from Legacy System
Safety